Pharmacogenetics of Carboxylesterase 1 Katriina Tarkiainen ACADEMIC DISSERTATION To be presented, with the permission of the Faculty of Medicine of the University of Helsinki, for public examination in Lecture Hall 3 of Biomedicum Helsinki 1, Haartmaninkatu 8, on 9 June 2017, at 12 noon. Page 1/7 Safety data sheet according to 1907/2006/EC, Article 31 Printing date Version number 1 Revision: 36.0.31 1 Identification of the substance/mixture and of the company/undertaking.

Builders' notes for Cape Henry 21 sailboat DUDLEY DIX YACHT DESIGN Cape Cutter 19 & Cape Henry 21 Builders' Notes - Updated 15 November 2009 CAPE HENRY 21 PHOTOS These pages show a mixture of CC19 and CH21 photos. Construction of the two designs is almost identical, so builders of each design will benefit from photos of the other. 1 ~ DECK STRINGER END SUPPORTS The ends of the deck stringers must be supported where they run out against bulkheads 2 and B. This is most easily done by cutting U-shape brackets from 12mm plywood and bonding each to the bulkhead face to form a socket in which the stringer end can be bonded. Fit 22x22mm [7/8x7/8'] square cleats against the bulkheads between the stringers to form a landing for the plywood deck. The diagram below shows how this works on bulkhead 2. The same principle applies at bulkhead B.

Similar doublers can be used to house the ends of berth supports and other joinery frames where they terminate against bulkheads. 2 ~ TRANSOM RADIUS The intended transom radius is shown on the lines drawing. This is the curvature for the outside of the transom. The transom and its doublers must be laminated over a temporary wooden mould shaped to the curve of the inside of the transom doublers, ie the transom and doubler thicknesses must be subtracted from the radius shown when building the mould.

The internal cut-outs from the doublers should be fastened to the mould as well but not glued to the transom. These will support the transom across the cutouts and ensure a more uniform curvature when the transom is removed from the mould.

We take into account we have the blog owner to be grateful to for that. The main explanations you’ve made, the easy blog navigation, the relationships you can give support to promote – it’s got many great, and it’s really aiding our son and the family understand that article is interesting, which is certainly very pressing. My wife and i got absolutely joyful that Jordan managed to complete his survey from the precious recommendations he made from your web page. It’s not at all simplistic just to choose to be giving out instructions that many some other people might have been making money from. Akt na spisanie uchebnikov v shkoljnoj biblioteke.

There will be some springback (straightening) of the laminated transom/doubler structure. It can be held to the intended shape by screwing two temporary curved frames to the inside or outside. These can be removed when the transom is restained by the hull and cockpit 3 ~ BUILDERS' FORUM There is an active builders discussion forum on Yahoo groups for builders of the Cape Henry 21. The address is.

You will need to register with Yahoo Groups to enter the forum. The issues discussed will be useful to builders of plywood Cape Cutter 19s as well. 4 ~ BULKHEAD A CORRECTION We have found a small error in the shape of the bottom panel of Bulkhead A as shown on patterns and kits supplied prior to May 10th 2004. The diagram below shows how to correct the error by gluing a wedge of plywood or timber onto the edge of the bulkhead. The wedge is 7mm thick at the backbone and tapers to 0mm at the chine. In the diagram below the red lines show the original shape of the bulkhead and the blue lines show what it must be changed to.

The stringer slot must also be adjusted to the new surface. The backbone has extra width to allow for the changing bevel angle that must be planed to suit the twist of the bottom skin angle. Establish this angle by making a saw cut into the backbone as an extension of the bulkhead edge from both sides. Cut the backbone down to the intersection of the two cuts made at each bulkhead and use them as a guide for trimming the backbone to width and angle. 5 ~ SPACERS TO CENTREPLATE SLOT Bill Empsall in NY has found that the centreplate case closes a bit under pressure from the bottom panels when these are being fitted.